How To Sew Repair Pants

Download Article

The crotch of your jeans is subject field to all kinds of wear and tear including stretching, thigh-rubbing, and horribly timed seam-splitting. It is the place nearly probable to get rips and tears, big and small. Instead of throwing damaged jeans abroad in defeat, there are a number of methods you lot can apply to fix a hole. A modest tear can be sewn together, while a larger pigsty will require patching. No matter how good or bad you are with a needle and thread, you can set a pigsty in the crotch of your jeans.

one
Cut loose threads abroad from the damaged area. You can fix some small holes without using a patch, just past sewing the sides of the small-scale hole or tear back together. Before you exercise this, yous should employ some scissors to clean up the edges of hole so there aren't any protruding loose threads. These will only go far the way as you work. Be careful not to brand the hole whatever bigger equally you exercise this.
- Only cut frayed threads, not the actual fabric of the jeans.^[1]
2

Thread the needle and tie the knot properly . Placing a knot at the far end of the thread will anchor it in the fabric once you lot starting time sewing. It tin can be frustrating to have to go along re-threading the needle, then be sure to go the thread tightly fixed.

Advertisement
iii
Stitch over the edges of the hole to prevent farther fraying. Seal the edges of the damaged area by looping thread around them and "tying" them close. Be sure not to stitch so close to the edge that the thread simply pulls more jean material loose. This stride is optional, but it can aid stop fraying around the pigsty and increase the strength of your fix.
- A coating stitch or buttonhole stitch are good options for this.
4
Sew the gap in the habiliment shut. Press or agree the textile so that the hole or tear in your jeans is nearly or completely shut. Then sew vertically beyond the hole to close it. (Note that you may have to sew together over this more once to brand it tight.) Showtime your stitches around a ½ inch to one side of the hole. Continue them to around ½ inch past the other side of the hole.
- As yous by the far-side of the hole, make the stitches gradually smaller.
- Pull the thread tight, tie it off, and trim information technology so at that place are no loose ends.^[2]
- Showtime these stitches at least ½ inch further back than the stitches you simply used to seal the edges of the gap.
- You could also do this with a sewing machine, but if information technology is a very small hole, it could be just as easy to set it past manus.
Advertising

ane

Cut away the loose threads. As with the method for sewing by hand, the commencement affair to do is to make clean up the hole or rip by trimming away any loose or dangling threads. Take care as you practice this and try to be as precise every bit possible.
2
Wind the bobbin on the sewing machine. Threading the needle on a sewing motorcar can be a bit catchy as they use two sources of thread, 1 from the bobbin and one from the spool. The outset matter to practice is wind the bobbin so that it is wrapped with thread. Once the spool and bobbin are in place on the top of your car, unravel a few inches of thread towards the far left side of the spool and wrap information technology around the nubbin on the left hand side of your machine.^[3]
- Then pull this thread to the bobbin, thread it through the small pigsty, and wrap information technology around the bobbin a few times to secure it.
- Fix the bobbin in place by pushing it to the right and so gentle press down on your peddle to air current the thread from the spool to the bobbin until you have as much thread as you need on the bobbin.
- Cutting the thread to split up the spool and bobbin, then remove the bobbin and switch off your machine.
3
Thread the spool. Have the end of the thread from the spool and pull it out to the left as before. This fourth dimension you are taking it down to the needle itself. Y'all will accept to accept the thread through a hook on the top of the auto and down along a aqueduct on the right hand side of the needle, earlier bringing it back upward to the superlative of the machine through another channel on the left, round the hook on the top and back down the left channel.^[4]
- Thread the needle through the hooks on the front and side of the needle itself before finally threading it through the needle itself.
- They will virtually likely exist arrows or directions marked on your car to make this easier.^[5]
- Most car follow the same basic pattern for threading.^[6]
4
Thread the bobbin. You accept threaded the needle from the spool above, and now it's time to thread information technology from the bobbin beneath. Open up up your auto to reveal the bobbin holder below the needle, and remove the small metal bobbin holder. Place your threaded bobbin in the holder and pull a few inches of thread out through the slit in the side, earlier returning the holder to the machine and endmost it.^[7]
- To get the thread from the bobbin up to the sewing surface, gently lower the needle with the manus bicycle while belongings the spool thread in your other mitt.
- Bring the needle dorsum up, carefully pull on the spool thread and the bobbin thread should appear.^[8]
5

Seal the edges of the rip with a zig-zag stitch. Centre a zig-zag stitch over the border of the fabric (and then that one-half of each stitch goes through the fabric the other half goes on the exterior to tie information technology shut). Sew forth each side of the hole to seal the edges and stop further fraying. Some sewing machines have a "buttonhole" setting or pedal that will work well for this purpose.
six
Sew beyond the hole or tear to close it. Push together the two sides of the hole with your hands to close it. One time information technology is securely in position, hold it in that location and position it beneath the needle on your sewing machine. Then, sew vertically beyond the hole to demark information technology and close information technology. As with the sewing past mitt method, be certain to first and finish your stitches ½ inch on either side of the hole.
- If you sealed the edges of the tear first, make sure you beginning these new stitches ½ inch further back to avoid pulling out the earlier stitches.
- If the hole is in an especially tight or inconvenient spot, moving your jeans through the automobile may nowadays a challenge and sewing by hand could be easier.
Advertisement

1

Tidy upwardly threads effectually the hole. Gluing on a patch is platonic for those who are not comfortable with a needle and thread, or simply desire a quick-fix. This might be a skilful option for piece of work jeans that are more important to y'all for their utility than their appearance. As with the other techniques, the first thing to do is to cut abroad any loose threads to make clean upwards the tear or pigsty.
2
Cutting a patch to size. Turn your jeans inside out and mensurate a piece of excess denim from an old pair of jeans, or whatever you lot want to patch the hole with. Brand sure there is plenty of space on the patch around the torn surface area so you tin apply the glue to the patch.
- You lot tin can buy fabric patches to apply instead of a scrap slice.
3
Apply the material mending glue to the patch. Y'all should follow the specific instructions on given on the bottle, but generally you will have to utilize mucilage to the edges of the patch. You volition need to take care to ensure that you don't put glue on a part of the patch that is going to exist showing through on the outside of your jeans. Printing the patch down over the pigsty and secure information technology there.^[nine]
- Different glues accept unlike amounts of time to dry out properly, simply information technology shouldn't have more than a few hours.
Advertisement

one
Prepare the pigsty you lot are going to patch. Some other easy alternative to sewing in a patch is to get an iron-on patch and employ that instead. As always, begin by cutting away excess threads so the pigsty is clear, before turning your jeans inside out and preparing the patch you are going to iron on to your jeans. Measure the hole with a tape measure out and cut the patch to size ensuring that there is a clearance of at least ½ inch around the hole.^[10]
- You tin mensurate this by center, but past using a tape measure out, you lot are less probable to get information technology wrong and end up wasting a patch by cutting it too small-scale.
- Cutting rounded corners on the patch will aid prevent it peeling upward.
two

Place a piece of scrap denim on the other side of the hole. Whether you are calculation the patch to the outside or the inside of the jeans, using a scrap of denim on the opposite side to the patch volition forbid the patch sticking to the other side of the jeans and potentially sticking the two sides together. This could seal your jeans shut and you might damage them if you then have to tear the leg open again.^[11]
iii
Iron the patch. With a pre-heated atomic number 26 you should at present place the patch over the pigsty and iron it down. How long you should practise this for could depend on the particular atomic number 26-on patches you have, so exist sure to read the instructions carefully and follow those. Typically it won't be for more than than thirty-60 seconds.
- Once information technology is set, remove the chip piece from the opposite side and you are good to go.
Advertisement

ane
Find a patch or suitable patching material. Sewing in a patch is the most comprehensive, merely also labour-intensive, way to fix a larger hole in the crotch of your jeans. This requires some basic control of a needle and thread or sewing machine, but when done well it could be neater and more reliable than gluing or ironing on a patch. Begin by finding a patch for the pigsty in your jeans.
- If placing the patch on the interior, cull a colour that closely matches the colour of your jeans to arrive wait more natural.^[12]
- You tin can be artistic with your patches if you want to make a statement or have some fun.^[13]
- Make sure the patch textile isn't thicker than the material of your jeans. If it doesn't give when y'all motion, it will force the jeans to tear effectually it instead.
two

Cutting out a patch at to the lowest degree 1 inch (2.five cm) larger on all sides than the hole. If you're cutting the patch from a weave material (like denim), cut diagonally against the weave; if you cut straight forth the criss or the cross of the weave, the edges will exist more likely to fray.
3
Place the patch over the hole, lay your jeans flat, and pin the patch to the jeans. Brand sure in that location is no bunching or pulling or the patch will stop upward bulky and stressed. Unless yous'd like to identify a colourful or conspicuous patch over the damaged area, slide the patch into the interior of the jeans, which should be kept correct-side out.
- Another selection is to use an fe on patch. Instead of pinning it, you can fe it on and so sew it in for more durability.
4

Run up in the patch with a sewing machine. Sew around the perimeter of the hole, removing pins as you become. Don't sew together besides nigh the edges or the torn material will fray and the stitches will fall out. Employ the machine's zig-zag stitch. You lot can also use a straight sew together, but use a back and forth motion which will itself lend a zig-zag shape to the stitching.^[14].
5
Or sew information technology in past paw. If you sew it in by paw utilize an clouded stitch. Poke the needle up through the patch about the edge. Plunge the needle and thread back down through the denim just outside the edge of the patch and somewhat forrad from where your needle emerged, creating a single diagonal stitch. In one case again poke the needle up through the underside of the patch (most the edge and slightly forward) to create another diagonal stitch on the underside of the fabric.
- Repeat until you've covered the unabridged perimeter of the patch in diagonal stitches. When you're washed, do the entire process again only this time, motion in the contrary direction to create diagonal stitches that cross the beginning set you made. The resulting outcome will look like a string of Xs.
- Be careful and make certain you are non sewing two sides of your jeans together, or sewing the material from the within of the pocket to the jean leg or crotch.^[xv]
6

Re-sew around the perimeter of the hole if necessary. Now that the patch is firmly in place, you can too run up closer to the edges of the tear to hold it down for a cleaner look. Re-sewing will reinforce the force of the patch.^[16] But be aware that adding layer upon layer of stitches can lead to your jeans becoming stiff and uncomfortable.
seven

Trim any loose edges. Once you have sewn in the patch, take some pinking shears or scissors and trim away any backlog material from patch. This could flap effectually, itch, or take hold of on things that might loosen the stitches around your patch.^[17] Press the stitches down with an iron to assistance polish out the stitches and your patching chore is complete.

Advertizement

Add together New Question

Question

How can I fix a pigsty in my jeans without sewing?

David Pew is a Professional Tailor and the Owner of Run up Generously based in Seattle, Washington. With over a decade of experience, David specializes in bespoke tailoring and alterations. He uses his experiences, skills, and middle for detail to produce the highest quality of products.

Professional Tailor

Expert Answer

You tin glue the patch on with material gum, but information technology won't be a permanent fix for your jeans.
Question

Do you lot sew together it on the inside?

Yes, go a needle and thread, sew on the within of your jeans by turning them within out.
Question

How tin I set my pants with glue?

Make sure your pants are aligned correctly. Then you can use fabric or super glue to mucilage the hem (the edge of the pants) where the hole is. Stick the two sides of the fabric together and concord them for a few seconds until the glue has had a gamble to set.

Inquire a Question

200 characters left

Include your electronic mail accost to go a message when this question is answered.

Submit

Article of clothing tight shorts or spankies under the pants you fixed only in case information technology rips again!
If you're using a sewing machine for the starting time time, have information technology slow.

Things Y'all'll Need

Sturdy sewing thread that matches (or compliments) the colour of your jeans.
A thick hand-sewing needle or a sewing automobile.
Scissors or pinking shears.
If mending a big hole, a patch.
Iron (optional)
Fabric mending glue (optional)

About This Article

Article Summary Ten

To ready a hole in the crotch of your jeans, brainstorm by cutting away any loose threads hanging from the tear so that they won't arrive your style as you're sewing. Then, thread a needle and tie a strong knot at the end of the thread. Stitch around the edge of the hole with a blanket stitch to prevent the textile from fraying even more than. Once you've sewn around the edges of the hole, press information technology close and sew beyond the pigsty to close it. Afterwards you've sewn the pigsty shut, pull the thread tight and tie a knot. Finally, trim the loose finish with scissors. If you lot want to learn how to patch your jeans to fix a larger pigsty, go on reading the article!

Did this summary assist yous?

Cheers to all authors for creating a page that has been read 980,582 times.

Did this article assistance yous?